How to Sharpen a Serrated Knife: One Scallop at a Time With a Tapered Rod

Disclaimer: As an Amazon Associate, I earn from qualifying purchases.

The usual advice about serrated knives is that you can’t sharpen them, so you throw them out. That’s only true for the cheap micro-serrated kind. A bread knife, a good serrated steak knife or a partly serrated pocket knife sharpens fine at home; you just can’t do it on a flat stone or in a pull-through slot, because neither one reaches into the scallops. A thin tapered rod does, one scallop at a time, and it only works the beveled side.

The steps below work with any tapered rod. The one I’d reach for is a fine diamond cone such as the DMT Diafold Serrated, because one rod fits both small and large serrations. If you want one tool that does serrations and plain edges in the field, my pocket knife sharpener guide has a few.

Why Serrated Knives Need a Different Method

A serrated edge is a row of small curved cutouts (called scallops or gullets) with points between them. The cutting happens inside the curves, and a flat stone only touches the points, so it flattens the teeth without sharpening the parts that do the work. A rod round enough to sit inside each curve is the only home tool that reaches them.

Most serrated kitchen and pocket knives are also ground on one side only. Look at the edge: one face has the scalloped bevel, and the other is flat right to the edge. You sharpen the beveled side and leave the flat side flat, apart from a light pass at the end to remove the burr.

The good news is that serrations stay useful far longer than a plain edge, because the points take the wear and the scallops stay protected. Most home bread knives need this once every year or two, not every few weeks. If you’re still choosing one, my best bread knife guide favors wide, rounded scallops, which also happen to be the easiest kind to sharpen.

Can This Knife Be Sharpened at All?

Check three things before you start.

  • Scallop size: wide, clearly separate scallops (bread knives, good steak knives, pocket knives with serrated sections) sharpen well. Tiny saw-like teeth you can barely see, the micro-serrated edge on cheap steak knives and “never needs sharpening” sets, can’t be sharpened in any useful way. Replace those.
  • Which side is beveled: most are beveled on one side. A few knives have serrations ground from both sides; treat each side the same way, with equal work.
  • Damage: a missing tooth or a bent tip can be cleaned up, but you’ll never rebuild a broken serration pattern by hand. For a valuable knife with real damage, a professional sharpener with a serration machine is the better call.

Steak knives sit in a gray area. A good serrated set is worth an hour once in a long while, but a budget set may cost less to replace than the time it takes. My steak knives guide covers which sets have serrations worth keeping.

How to Sharpen a Serrated Knife With a Tapered Rod

This works with any of the rods above. Go slowly the first time; after a knife or two, a bread knife takes about ten minutes.

  1. Find the beveled side. Hold the knife edge up under a light. The side with the visible scalloped bevel is the one you sharpen.
  2. Color the bevel with a marker. Run a permanent marker along the beveled edge. When the ink disappears exactly where you want, your angle is right; if the rod only takes ink off the top of the bevel or off the very edge, adjust.
  3. Match the rod to the scallop. Lay the rod in the first scallop near the heel and slide it along until its thickness fills the curve. Use only the part of the rod that is no wider than the scallop, or you’ll widen it and round the points.
  4. Hold the rod at the bevel angle. Tilt it to lie flat against the existing bevel, which is usually steeper than people expect. The marker tells you if you’ve got it.
  5. Stroke outward, toward the edge. Push the rod through the scallop from the spine side to the edge side in short, light strokes, rotating it slightly so the whole curve gets contact. Five or six strokes per scallop is a good start.
  6. Feel for the burr. Run a finger gently across (never along) the flat back side under that scallop. A faint rough lip of metal means you’ve sharpened all the way to the edge. Move to the next scallop and repeat to the tip.
  7. Remove the burr from the flat side. Lay the flat back of the blade completely flat on a fine stone, a ceramic plate or a strop and make two or three light passes. Keep it dead flat; tilting it puts a bevel on the back and ruins the geometry.
  8. Test and clean. Slice a tomato or the crust of a loaf. If one stretch still drags, give those scallops a few more strokes. Wash the blade to remove metal dust.

Leave the points alone. They’ll be sharp again once the scallops are, and grinding them shortens the teeth.

Bread Knives, Steak Knives and Pocket Knives

Bread knives

Bread knives have the widest scallops, so use the thick end of the cone and count strokes so every scallop gets similar work. On a long blade it’s easy to lose your place; a piece of tape on the spine as a marker helps. My guide to sharpening Wüsthof knives covers the bread knives in that range, which work exactly this way.

Serrated steak knives

Steak knife scallops are much smaller, so you’ll work with the thin end of the rod and lighter pressure. Do one knife first and compare it with the rest of the set before committing the afternoon.

Partly serrated pocket knives

Sharpen the plain part of the blade first on a stone or guided sharpener, then the serrated section with the rod, then remove the burr along the whole flat side. My pocket knife sharpening guide covers the plain-edge part in more detail.

What Not to Use on Serrations

Pull-through sharpeners

The V-shaped carbide slots in most pull-throughs are made for plain edges. Dragged through them, serrations get their points ground down and the scallops never touched. Some sharpeners have a slot marked for serrated knives; that slot hones the points lightly and is fine for a quick refresh, but it’s no substitute for a rod.

Flat stones on the serrated side

A whetstone or diamond plate only reaches the tips of the teeth. The flat stone belongs on the flat back side, for burr removal, and nowhere else on a serrated blade.

Electric sharpeners

Only use one if the maker says it handles serrated knives, and then only in the stage it names. My knife sharpener guide notes which models say so.

Heavy pressure

Pressing harder doesn’t speed things up on a small scallop. It tilts the rod off angle and rounds the points. Let the rod do the cutting.

Tools I’d Use

Any rod that fits inside your scallops will do. These three cover kitchen and pocket knives between them.

1. DMT Diafold Serrated Diamond Sharpener, Fine: Best All-Round Rod

Diamond Machining Technology (DMT) Diafold Serrated Diamond Knife Sharpener, Fine (FSKF), 4"

Check Price on Amazon

The cone tapers from a quarter inch to a sixteenth, so it fits a bread knife’s wide curves and a steak knife’s tight ones, and fine diamond (25 micron per DMT) cuts quickly with light pressure. It’s made in the USA and the handles fold over the rod for storage. There’s no angle guide, so the marker trick matters, and for badly worn teeth DMT sells the same tool in a coarse grit.

2. Gatco Tri-SEPS Serrated Edge Sharpener: Gentlest for Beginners

Gatco 4.5" Tri-SEPS Ceramic Rod Sharpener for Serrated & Plain Edge Knives | Triangular Alumina Ceramic Rod, Built In Sharpening Angle Guide, Rubberized Ends, Bead Chain, Portable Field Edge Repair Tool

Check Price on Amazon

A small triangular ceramic rod with two radius sizes and a built-in angle guide. Ceramic removes very little steel, so it’s the safe choice for a first attempt on a good bread knife. The trade-off is speed: on a really dull knife it takes a long time, and two curve sizes fit fewer scallop shapes than a cone.

3. SHARPAL 178N 3-in-1 Diamond Sharpening Rod: For Partly Serrated Pocket Knives

SHARPAL 178N 3-In-1 Pocket Knife Sharpener, 4-Inch 600 Grit | Diamond Sharpening Rod, For Straight & Serrated Blades and Hooks, Compact Tool, Aluminum Handle, Gifts for Men

Check Price on Amazon

Two 600 grit diamond rods in one aluminum handle: a 3.5 inch tapered one for serrations and a 4 inch round one for the plain part of a combo edge. That pairing is what a partly serrated folder needs on a trip. The rods are short, so long kitchen bread knives are easier on the DMT.

FAQ

Can you sharpen a serrated knife?

Yes, if the serrations are big enough to see clearly. Work a tapered rod through every scallop on the ground side, then remove the burr from the flat side; tiny micro-serrations on cheap knives aren’t worth the effort.

How do you sharpen a serrated knife without a sharpener?

You can’t do it well. The bottom of a ceramic mug or a flat stone only reaches the tips of the teeth. A round object narrow enough to fit the scallops, such as a fine round file, works in a pinch, but a tapered rod is the right tool.

Do you sharpen both sides of a serrated knife?

Usually only the beveled side. Most serrated knives are flat on the back, and that side only gets two or three dead-flat passes to remove the burr. If your knife is beveled on both sides, sharpen both equally.

How often should a serrated knife be sharpened?

Rarely. A home bread knife usually needs it every year or two; sharpen when it starts tearing soft bread or skidding on tomato skin instead of biting straight in.

Can you use a honing rod on a serrated knife?

A standard honing steel only touches the points. A thin ceramic rod that fits inside the scallops can hone them lightly between sharpenings, which is what the serrated rods above are built for.

Is it worth sharpening cheap serrated steak knives?

Usually not. Budget sets with micro-serrations can’t really be sharpened, and with sets that can, the time spent often costs more than replacing them.

Final Verdict

Sharpening a serrated knife comes down to three habits: work inside each scallop with a rod that fits it, stay on the beveled side, and take the burr off the flat back with the blade lying flat. Do that once every year or two and a good bread knife lasts for decades; if the teeth are tiny micro-serrations, replace the knife instead.

For a burr-removal routine that also works on plain edges, see my guide to stropping a knife.

Leave a Comment